Call for door repair(984) 217-8021

Service 03 of 09 · Charlotte, NC

Panic Bar & Exit Device Repair in Charlotte, NC

A panic bar has two jobs: let people out with a single push, and relatch the door behind them. When a push bar sticks, a latch won't retract, or a pair of doors won't stay latched at night, both safety and security are affected. We repair and replace exit devices on Charlotte commercial doors.

Symptom → cause → fix

What's wrong with the door?

Match what you're seeing to the usual cause. We confirm on site before replacing anything.

Panic Bar & Exit Device Repair: common symptoms in Charlotte buildings
SymptomLikely causeTypical fix
Bar is hard to push or sticks downWorn or dirty internal mechanismService the mechanism or replace the device
Latch doesn't fully retractOut-of-adjustment linkage or worn latchAdjust the linkage, replace worn latch parts
Pair of doors won't latch at the top or bottomVertical rods out of adjustment or bentRe-adjust or replace the rods and strikes
Door has to be pulled shut to relatchCloser weakness or leaf sag, not the deviceCorrect the closer and alignment first. See door closer repair
Key or outside lever won't let you inWorn or broken connection between the outside trim or cylinder and the deviceRepair or replace the trim or cylinder, then confirm the exit still releases from inside with one push. See commercial door lock repair

The basics

How it works and why it fails

A panic bar, also called an exit device or push bar, is a latch that you release by pushing a bar or pad across the door. Inside the housing, the bar is connected to a linkage that pulls the latch bolt back out of the strike. Springs return the bar and push the latch back out when you let go. On a single door, the latch usually catches a strike on the frame. On a pair of doors, rods may run to latches at the top and bottom of the door instead.

Exit devices fail because they work hard and get abused. They are pushed with hips, carts and full body weight, often many times a day. Internal springs weaken, pivots wear, and the linkage that pulls the latch can drift out of adjustment. Grit and debris build up inside the housing and make the bar stiff. The latch bolt and strike wear where they meet, so the latch may catch only when the door is pushed or pulled shut. Vertical rods bend when doors are forced or carts strike the bottom of the door.

Many exit device problems are caused by the door around them. If the door has sagged, the latch no longer lines up with the strike. If the closer is weak, the door does not swing hard enough to push the latch over the strike and catch. If the frame has shifted, the gap between paired doors changes, and the latches fall out of alignment. A good repair considers the device, the door, the closer and the frame together, because fixing only one often leaves the problem in place.

The parts that matter

Panic Bar & Exit Device Repair: components and how they fail
PartWhat it doesHow it fails
Push pad and chassisThe push pad or crossbar is what people press, and the chassis inside the housing holds the springs and linkage that retract the latch.When springs weaken or the chassis wears, the bar sticks down, feels gritty, or does not fully return. A cracked housing or loose end cap often means the device is near the end of its life.
Latch bolt and rim strikeOn a rim device, the latch bolt projects from the device and catches a strike mounted on the frame or mullion.Worn latches and strikes stop catching cleanly. You notice the door bouncing back open or needing a push before it latches.
Surface vertical rodsExposed rods run from the device to latches at the top and bottom of the door, usually on pairs of doors.Rods bend or go out of adjustment as the door is used. The top or bottom latch stops engaging, and the doors may be pushed open from outside.
Concealed vertical rodsRods and latches run inside the door, so they are hidden from view, with latches at the top and sometimes the bottom of the door edge.Adjustment is harder because the rods are inside the door. Failure shows as a pair that will not latch at the top or bottom, often only after the door has been slammed or forced.
Dogging mechanismA key, hex key or cylinder that holds the bar down so the door works as push-pull during business hours.Dogging can stop holding or fail to release. Fire exit hardware is not allowed to have mechanical dogging, so a dogged device on a fire door is a problem to fix, not just a feature.
Outside trimThe lever, knob, pull or key cylinder on the outside of the door that controls entry from that side.Trim parts wear or the connection to the device slips. You notice the outside lever spinning loosely, the key not retracting the latch, or the door unlocked when it should be locked.

On-site diagnosis

What we check

Device mechanism

Push-pad travel, return spring, and full latch retraction.

Strike and alignment

Where the latch meets the strike, and whether the door has dropped.

Rods and pairs

Top and bottom rods, latches and the fit between the two doors on paired openings.

Technician adjusting latch hardware on the edge of a commercial door with a screwdriver
Latching depends on the exit device and the strike it engages, so both are checked together.

Repair or replace?

Worn latches, springs and rods can be replaced on many devices. Cracked chassis, obsolete models without parts, and devices on fire-rated doors that aren't listed for fire exit use should be replaced. A replacement has to suit the door's rating and function, not just fit the old screw holes.

Panic Bar & Exit Device Repair in Charlotte

Breweries, event spaces and restaurants in South End, NoDa and Camp North End often have exit doors that see heavy use on busy nights. Vertical rod devices on those paired doors go out of adjustment quickly. If a pair of doors won't stay secure overnight, call before the weekend.

Step by step

How a panic bar & exit device repair visit works

  1. We confirm the device type and door rating

    We identify whether the device is a rim, surface vertical rod, concealed vertical rod or mortise type, and check the door and frame for a fire rating label. The rating determines what kind of replacement parts or devices are allowed, so we confirm it before anything is removed.

  2. We test the exit from both sides

    We push the bar from the inside and check how much force it takes and whether the latch retracts fully. From the outside, we check the trim, key and lever operation. We also watch whether the door relatches on its own when it closes, without needing to be pulled shut.

  3. We check alignment and the closer

    We check where the latch meets the strike and whether the door has dropped or shifted. On pairs, we check the gap between the doors and the condition of the top and bottom strikes. If the closer is too weak to latch the door, we note it so it can be corrected with the device.

  4. We service, adjust or replace parts

    Depending on the problem, we clean and adjust the mechanism, replace worn latches, springs and strikes, or re-adjust and replace vertical rods. If the device is cracked, obsolete or not suitable for the door's rating, we recommend a replacement that matches the door, its function and its rating.

  5. We cycle and verify egress

    After the work, we operate the door repeatedly from inside and outside, confirm the latch retracts with a single push and relatches every time, and check any dogging, key or electric functions. The goal is an exit that opens easily for anyone inside and stays secure from outside.

Safe checks

What you can check before you call

A few minutes of observation makes the phone call faster and the diagnosis more accurate.

Do Safe

  • Push the bar slowly and watch the latch. If it does not pull back all the way into the device, note it when you call.
  • Check whether the door latches when it closes on its own. If you have to push or pull it shut, mention that, since it points to the closer or alignment.
  • Look on the door edge and frame for a fire rating label. A metal or embossed label tells us what hardware the door requires.
  • On a pair of doors, look at the top and bottom latches and strikes. Bent rods, missing strikes or worn floor holes are useful details.

Don't Avoid

  • Don't lubricate the mechanism with heavy grease or oil. It traps dirt inside the housing and can make the bar stiffer over time.
  • Don't add a padlock, chain or slide bolt to secure a door that won't latch. Any lock that stops the exit from opening with one push is a life safety hazard.
  • Don't dog down a fire exit device with tape or a wedge. Fire doors have to latch, and holding the latch back defeats the door's fire rating.

Expert answers

Panic Bar & Exit Device Repair: the decisions that matter

Rim, vertical rod or mortise exit devices

Exit devices come in three main styles, and the right one depends on the door and the opening. A rim device has a single latch at the end of the bar that catches a strike on the frame. It is the simplest and most common style on single doors and is easy to service. On a pair of doors, a rim device needs a center post, called a mullion, to latch against. A vertical rod device latches at the top and bottom of the door instead of the edge. Surface vertical rods are mounted on the face of the door and are easy to reach. Concealed vertical rods run inside the door, which looks cleaner and protects the rods, but makes adjustment and repair more involved. Vertical rod devices let a pair of doors open without a center post, which is useful for moving equipment through. A mortise exit device uses a lock body set into a pocket in the door edge, much like a mortise lock. It is strong and secure but requires a door built for it. Replacing a device with a different style usually means changes to the door or frame, so most repairs keep the same type.

When a pair of doors needs a removable mullion

Pairs of doors are hard to secure because there is nothing in the middle for the latches to catch. Vertical rod devices solve this by latching into the head of the frame and the floor. They work well, but their top and bottom latches are exposed to wear and need regular adjustment. In busy venues, such as breweries and event spaces around Camp North End or South End in Charlotte, bottom rods often take damage from carts and foot traffic. A removable mullion is an alternative. It is a vertical post that sits between the two doors, so each door can use a simple rim device that latches against it. When wide equipment needs to pass, the mullion can be unlocked and lifted out. Rim devices on a mullion are generally easier to keep adjusted than vertical rods. The tradeoff is that the mullion has to be put back and locked in place, and it must not block a required exit width while it is in use. On fire-rated pairs, the mullion and devices have to be suitable for that use. This is a good option to discuss if your rods keep going out of adjustment.

Make it last

How to prevent the next failure

Let the closer do the work

A door that slams shuts hard on the latch and strike, and a door that drifts closed never latches. Keeping the closer adjusted so the door closes firmly but not violently protects the exit device and strikes from wear and damage.

Watch for cart and dolly strikes

In kitchens, warehouses and loading areas, carts and dollies often hit the bottom of the door. That impact bends bottom rods and strikes. Kick plates, door edge guards or a less-bottom-rod setup can reduce damage on doors that take this abuse.

Keep thresholds and floor strikes clean

Bottom latches on vertical rod devices drop into a strike in the floor or threshold. Dirt, gravel and ice packed into the strike stop the rod from seating. Sweeping the threshold and clearing the strike regularly keeps bottom latches working.

Test exits as part of routine checks

Pushing each exit device once a week and checking that the door relatches on its own catches problems early. Many facility managers fold this into their regular walk-through. Fire doors also need a documented annual inspection under NFPA 80.

What affects the cost of panic bar & exit device repair

We don't quote flat prices without seeing the door. These factors set the scope.

Device type
Rim devices are the simplest to service and replace. Surface vertical rod devices add top and bottom latches and strikes. Concealed vertical rod and mortise devices are built into the door, which takes more time to service and may limit replacement options to models that fit the existing prep.
Fire rating
On a fire-rated door, any replacement has to be listed fire exit hardware compatible with the door. That can narrow the choice of devices, and in some cases the existing device has to be replaced even if it still operates because it is not suitable for the rating.
Single door or pair
Pairs of doors need more hardware: two devices, rods or a mullion, and strikes that have to line up. Adjusting one door affects how the other one latches, so pairs take longer to set up and test than a single door, and both leaves are checked together.
Outside trim and functions
Lever trim, key cylinders, night latch functions, alarmed devices and electric latch retraction tied to access control all add parts and setup time. Matching the existing functions on a replacement keeps the door working the way the business depends on, from opening hours to after-hours security.
Condition of the door and frame
If the door has sagged, the frame has shifted, or the closer is failing, those problems often have to be fixed before the exit device can latch reliably. Reinforcing stripped mounting holes on hollow metal or aluminum doors can also add to the scope of the visit.

Before you call

Have this ready

These details let us scope the job on the phone and send the right parts.

Call (984) 217-8021
  1. Single door or a pair
  2. Rim device, or rods running to the top and bottom
  3. Whether it's a fire-rated door (look for a label on the door edge or frame)
  4. Brand name on the push pad
  5. Who can approve the work: owner, tenant or property manager

FAQ

Panic Bar & Exit Device Repair questions

Can I chain or block a sticking exit door until it's fixed?

No. Never chain, lock out or block an exit while the building is occupied. Call for repair and tell the building manager. Any temporary measure has to keep the exit usable.

Is a panic bar the same as fire exit hardware?

No. Fire exit hardware is panic hardware that is also listed for use on fire-rated doors, and it can't be dogged open. Fire doors need the listed type.

Why won't my double doors latch at the top?

On vertical rod devices, the top latch and its strike go out of adjustment as the doors and rods wear. Re-adjusting the rods usually fixes it unless parts are bent or broken.

What does dogging a panic bar mean?

Dogging holds the push bar down so the latch stays retracted and the door works as a push-pull door. It is used during business hours so people can enter without a key. It is done with a hex key, a key cylinder or an electric function. Fire exit hardware does not allow mechanical dogging, because fire doors have to latch to work.

Can a panic bar be connected to an access control system?

Yes. Many exit devices can be fitted with electric latch retraction, which pulls the latch back on a signal from a card reader or timer, or with electrified outside trim that unlocks the lever. The door must still open from inside with a single push at all times. Whether your existing device can be converted depends on its model and condition.

Why does my exit door open from the outside when it's supposed to be locked?

Usually the latch is not fully engaging the strike. The door may have sagged, the strike may be worn, or a vertical rod latch is not catching. On some devices, outside trim set to the wrong function will leave the door unlocked. A quick check of the latch, strike and trim function usually finds the cause.

Do I need a panic bar on my business's exit doors?

It depends on the occupancy type, the number of people the space is designed to hold, and whether the door is fire rated. Assembly spaces such as restaurants, bars and event venues commonly require panic hardware on exit doors. Your building's code requirements are set by the local authority in Charlotte. We can tell you what hardware is on the door and what it is listed for.

Does changing an exit device need anyone's approval?

Often, yes. In a leased building, exit and fire-rated doors are usually controlled by the owner or property manager. Replacement devices must suit the door's rating and function. Some changes, such as adding delayed egress or electrified functions, may also need review by the code official, so mention any planned change of function when you call.

Related door repairs

Need panic bar & exit device repair in Charlotte?

Call and describe what the door is doing. We'll tell you what's likely wrong and get it fixed.

Call (984) 217-8021
Commercial door repair · CharlotteTap to call (984) 217-8021